CDC Guidelines for Cleaning Companies: A Practical Guide
A cleaning plan should do more than make a facility look tidy. It needs to reflect how people use each space, which surfaces receive the most contact, and what staff can safely clean with the products provided. The cdc guidelines for cleaning companies offer a useful starting point, but they don’t call for the same routine in every building. A dental clinic, a corporate office, and a busy warehouse have different needs. Facility managers and cleaning providers can work together to set clear tasks, schedules, and product procedures. This guide explains how to apply public health recommendations in practical ways, protect cleaning staff, and keep service consistent as facility needs change.
Key Takeaways
- Set cleaning schedules around how each space is used: Give high-traffic areas and shared surfaces appropriate attention, and adjust routines when occupancy or conditions change.
- Use disinfectants only when needed and follow the label: Confirm the product suits the surface, observe its contact time, and provide staff with task-specific PPE and training.
- Put procedures in writing and review them regularly: Document tasks, schedules, products, and responsibilities, then update the plan with facility managers when needs or guidance change.
What Do CDC Guidelines Recommend for Cleaning Companies?
CDC guidance gives cleaning companies a practical framework: clean surfaces regularly, disinfect when the situation calls for it, and follow product-label directions. The right plan depends on how a facility is used, how many people share its spaces, and whether a specific health concern requires extra steps. A busy retail entrance, a shared office kitchen, and a low-traffic storage room may need different schedules.
Facility managers and cleaning providers can work together to identify priority areas, set service frequencies, and clarify which tasks are included. A written plan also helps staff follow the same procedures across shifts and locations. It should name the surfaces to be cleaned, explain when disinfection is needed, and list the approved products and instructions for their use.
Guidance can change as public health recommendations and facility needs evolve, so review plans regularly. The CDC’s cleaning and disinfecting guidance offers a useful foundation for routine settings. Medical and dental facilities may also need to follow additional infection-control rules. The sections below explain how cleaning teams can apply these principles in day-to-day work.
Distinguish cleaning, sanitizing, and disinfecting
Cleaning, sanitizing, and disinfecting describe different processes. Cleaning removes dirt and many germs from a surface, typically with soap or detergent and water. Sanitizing reduces germs to levels considered safe under public health standards. Disinfecting uses a product to kill germs on surfaces.
These steps serve different purposes, so a cleaning plan should specify which one is needed for each task. For routine care, cleaning is often sufficient. Disinfection may be appropriate when a surface is contaminated, someone has been ill, or facility rules call for it. Sanitizing is often used on food-contact surfaces and in other settings where its product label allows.
Train staff to recognize the distinction and check product directions before starting a task. This helps avoid unnecessary chemical use and supports consistent service across offices, retail spaces, and other facilities.
Clean surfaces before disinfecting when product labels require it
Some disinfectants work best when staff first remove visible dirt and residue. If the product label calls for pre-cleaning, use soap or detergent and water to clean the surface before applying the disinfectant. Other products are designed to clean and disinfect in one step, so staff should follow the specific label rather than assume every surface needs the same process.
The label also explains how much product to use, which surfaces it can be applied to, and how long the surface must stay wet. This period is called the contact time. Staff should allow the surface to remain wet for the full time stated on the label, then follow any additional instructions, such as rinsing.
Clear work instructions can help teams apply these steps reliably across shifts and locations. When a client requests a change in product or procedure, confirm that the new approach matches the label and the facility’s requirements.
Prioritize high-touch surfaces and shared equipment by risk
Door handles, light switches, counters, faucets, phones, keyboards, and shared tools are touched by many people throughout the day. Include them in the cleaning plan, then set a suitable frequency based on traffic, occupancy, surface type, and how equipment is used. A busy reception desk may need more frequent attention than a meeting room used only occasionally.
Risk-based planning helps cleaning teams focus their time where it is most useful. Consider whether people share a surface or item, how often it is touched, and whether the space serves people who may be more vulnerable to illness. Routine cleaning is suitable for many everyday situations, while disinfection may be needed when circumstances or facility rules call for it.
Review the task list with the facility manager when occupancy, operations, or health concerns change. This keeps schedules aligned with how the building is actually being used.
Apply CDC guidance alongside EPA, OSHA, and local requirements
CDC recommendations are one part of a safe cleaning program. The EPA registers antimicrobial products and provides List N, a resource for identifying products that meet its criteria for use against SARS-CoV-2. Check the label to confirm that a product is intended for the surface and use in question, and follow its application directions.
Employers also need to protect cleaning staff from chemical and workplace hazards. OSHA’s Hazard Communication Standard addresses chemical labels, safety data sheets, and worker training. State and local rules, as well as facility-specific policies, may add requirements.
Facility managers can help by sharing relevant site procedures with the cleaning provider before work begins. Together, they can confirm approved products, required protective equipment, access rules, and any special protocols for the building. Regularly checking applicable guidance helps keep the cleaning plan current and practical.
How Often Should Cleaning Companies Clean and Disinfect?
Set schedules based on occupancy, traffic, and facility use
There is no single schedule for every facility. A busy clinic, a professional office with limited visitors, and a large warehouse all have different cleaning needs. Work with the facility manager to identify when people use each area, how many people share it, and which tasks are needed daily, weekly, or periodically.
Entrances, restrooms, break rooms, reception desks, and shared meeting spaces may need more frequent attention than private offices or low-traffic storage areas. A cleaning plan should reflect actual use and operating hours, not rely on the same checklist for every building. The CDC’s guidance for cleaning public spaces notes that regular cleaning is generally sufficient in most situations. Documenting priorities helps cleaning staff complete essential work with minimal disruption.
Consider surface type, users, and contamination risk
The surface and its purpose should guide the cleaning method. Desks, floors, glass, upholstery, and electronic equipment may need different tools or products. Follow product labels and manufacturer instructions to clean effectively and help prevent damage.
Consider who uses the space and what activities take place there, too. Medical and dental clinics, daycare centers, food-preparation areas, retail spaces, and warehouses each have distinct requirements. Shared equipment and frequently touched surfaces may need closer attention when many people use them throughout the day. Review facility-specific standards with the manager and include any special instructions in the service plan. The CDC’s facility cleaning guidance emphasizes following practices and requirements suited to the type of facility.
Increase cleaning when illness, exposure risk, or operations change
A routine schedule may need to change when someone who is ill has spent time in the facility, an area sees an unexpected increase in use, or operations shift. Facility managers should tell the cleaning provider which areas may be affected and when they were last occupied. The team can then determine the appropriate cleaning and disinfection steps.
Avoid applying extra treatment throughout a building without assessing the situation. Confirm the areas involved, access needs, product directions, and current public health recommendations before work begins. Guidance can change, so check current recommendations rather than relying on an old response plan. The CDC’s cleaning and safety guidance advises cleaning and disinfecting a space when someone who is sick or tested positive for COVID-19 has been there within the previous 24 hours. Document any changes to the schedule and communicate them to occupants.
Avoid unnecessary disinfection when routine cleaning is sufficient
Disinfection does not replace routine cleaning. Dirt and debris can interfere with some disinfectants, so clean surfaces first when the product label requires it. Disinfect when facility needs, applicable requirements, or current public health guidance call for it, and follow the label’s application directions and contact time.
Using disinfectants more often than needed can add cost, interrupt operations, and expose staff or occupants to chemicals without a clear benefit. Set a schedule based on the facility’s actual conditions, then review it when occupancy, use, or guidance changes. In most situations, the CDC’s public-space guidance identifies regular cleaning, at least once a day, as sufficient for removing viruses that may be on surfaces. Use additional disinfection when circumstances warrant it, and record the reason in the cleaning plan.
How Should Staff Respond to a Confirmed COVID-19 Case?
A confirmed case calls for a clear, coordinated response, not rushed or unnecessary disinfection. The facility manager and cleaning provider should identify the spaces that need attention, follow current guidance, and protect staff and building occupants throughout the process.
Coordinate with the facility manager and identify areas the person used
Start by contacting the facility manager or designated site representative. Confirm which areas the person used and when they were last there. Protect the person’s privacy by sharing only the information staff need to complete their work.
Together, identify relevant spaces such as workstations, meeting rooms, restrooms, break areas, and shared equipment. The manager can arrange access restrictions while cleaning is underway and tell occupants when affected areas are ready to use. Keep restrictions focused on the spaces that require attention, rather than closing areas without a clear reason. Before work begins, agree on the tasks, who will complete them, and who will communicate updates to building occupants.
Follow current public health guidance for cleaning, disinfection, and access
Follow current public health recommendations and the product label to determine which surfaces need cleaning or disinfection. Clean visibly dirty surfaces first. If disinfection is appropriate, pay particular attention to frequently touched surfaces in the areas the person used, and follow the label’s directions for application and contact time. Routine cleaning may be appropriate elsewhere, depending on current guidance and the facility’s circumstances.
The facility manager and cleaning provider should agree on access procedures before work begins. Guidance can change, so check the CDC’s cleaning and disinfecting recommendations and any applicable state or local requirements. Record the areas addressed, the products used, and when the work was completed.
Consider time since occupancy and room ventilation
Ask when the person was last in the space. The time elapsed can affect the recommended response, so consult current public health guidance instead of relying on a fixed waiting period. Keep others out of an area while staff prepare to clean, following the facility’s access procedures.
Where practical and safe, improve airflow by opening windows or doors, or ask the facility manager whether ventilation settings can be adjusted. Do not change building systems without authorization, particularly in facilities with specialized ventilation. The CDC’s guidance on ventilation in buildings explains ways to improve indoor air quality. Ventilation complements cleaning, but it does not replace the need to follow product directions or site procedures.
Use appropriate PPE and follow safe work procedures
Before starting, read the disinfectant label and safety data sheet to determine what personal protective equipment (PPE) the task requires. Depending on the product and application method, staff may need gloves, eye protection, or other protective equipment. Check that items fit properly and are in good condition, and follow training for putting them on and removing them safely.
Follow site procedures for chemical handling, ventilation, waste disposal, and hand hygiene. Never mix cleaning products, and do not use an application method the product label prohibits. If staff are unsure about PPE, product use, or a possible exposure, they should stop and contact a supervisor. Employers can refer to OSHA’s PPE guidance when setting task-specific protections.
Which Disinfectants Should Cleaning Companies Use?
Choose a disinfectant according to the facility’s needs, the surfaces being treated, and the germs the product is intended to address. A product suitable for a hard countertop may not be appropriate for upholstery, electronics, or food-contact surfaces. Check the label before adding a product to a cleaning plan, and confirm staff can use it safely for the task.
The EPA registers disinfectants for specific uses, while the CDC provides public health guidance. Cleaning teams should follow product labels and workplace safety requirements, and coordinate with facility managers about any additional site protocols.
Choose an EPA-registered product labeled for the intended surface and use
Select an EPA-registered disinfectant whose label lists the surface and use you need. Check whether it is intended for hard or soft surfaces, whether it can be used on food-contact areas, and whether rinsing is required after application. These details are important in facilities such as clinics, offices, kitchens, and manufacturing sites, where surfaces and cleaning needs vary.
Also review which organisms the product is designed to address. Match those claims to the facility’s cleaning plan rather than assuming one disinfectant works for every situation. The EPA’s guidance on pesticide product labels explains how labels identify approved uses and provide directions for applying products safely and effectively.
Check EPA List N when a product is needed for SARS-CoV-2
If a cleaning plan calls for a disinfectant effective against SARS-CoV-2, the virus that causes COVID-19, consult the EPA’s List N. It identifies products that meet EPA criteria for use against the virus. Check the exact product name and confirm the intended application matches the product’s label.
List N helps with product selection, but it does not replace the label. Before assigning a product to a task, verify that the surface, application method, and contact time are appropriate. If a facility has specific infection-control protocols, check with its manager to make sure the selected disinfectant fits those requirements.
Follow label directions for dilution, application, and contact time
Use the concentration and application method stated on the product label. Some disinfectants are ready to use; others require dilution. Measure carefully and follow the listed instructions to help ensure the product works as intended and to avoid residue or damage to surfaces.
Pay close attention to contact time, the length of time the surface must remain visibly wet for the disinfectant to work as directed. If it dries before that time has passed, reapply it only as the label instructs. Check for additional directions about ventilation, rinsing, and protective equipment. Keep labels accessible to employees so they can confirm instructions while working. The EPA explains how product labels guide safe use.
Never mix chemicals or use application methods the label prohibits
Never mix a disinfectant with another cleaner or chemical unless the product label specifically permits it. Combining products can create hazardous fumes or cause dangerous reactions. Keep chemicals in their original, labeled containers, and ensure staff know where to find the safety data sheet and how to follow the facility’s spill-response procedures.
Use only the application methods listed on the label. Do not fog, spray, or apply a product to a surface if those uses are not permitted. Disinfectants should not be applied to people. Before using a product in an occupied space, confirm the label allows it and that any required precautions are in place. Clear written instructions and hands-on training help cleaning teams apply products consistently and safely.
How Can Companies Protect and Train Cleaning Staff?
Cleaning staff work in many environments, from offices and retail spaces to clinics, schools, and warehouses. Each task can bring different risks, including chemical exposure, wet floors, equipment hazards, and contact with contaminated surfaces. Employers should identify those risks before work begins, then provide the procedures, training, and protective equipment that match the job. OSHA’s personal protective equipment guidance outlines employers’ responsibilities for assessing hazards and selecting appropriate PPE.
A reliable safety program also depends on coordination between the cleaning provider and the facility manager. Before service starts, clarify site rules, restricted areas, emergency contacts, and any special requirements for handling waste or cleaning sensitive spaces. Give employees instructions they can refer to during their shift, and make it easy to ask questions or report concerns. Regular training and follow-up help staff apply procedures consistently, even when products, equipment, or facility needs change.
Provide task-appropriate PPE and safe work procedures
Select personal protective equipment (PPE) based on the task, the product label, the safety data sheet, and the hazards identified at the site. Depending on the work, employees may need gloves, eye protection, protective clothing, or other equipment. Make sure PPE fits, is in usable condition, and is replaced when damaged or contaminated. Train staff to put it on, remove it, and clean or dispose of it safely.
Written procedures should explain how to prepare an area, complete the task, and protect workers and building occupants. Include steps for placing wet-floor signs, limiting access, and securing supplies where relevant. Review procedures whenever the task or site conditions change, and invite employees to flag steps that are unclear or difficult to follow.
Train staff to read product labels and safety data sheets
Teach employees to check a cleaning product’s label before every use. Labels describe the product’s intended use and give directions for dilution, application, contact time, and precautions. Staff should use products only as directed and only on suitable surfaces. They should not guess at measurements or use an unlabeled container.
Safety data sheets (SDS) provide further information about chemical hazards, first aid, storage, and spill response. Keep current SDS documents accessible during work, and show employees how to find the details they need. OSHA’s Hazard Communication Standard explains requirements for communicating chemical hazards in the workplace. If a label is missing or unclear, employees should stop and ask a supervisor rather than improvise.
Demonstrate safe chemical handling, equipment use, ventilation, and spill response
Demonstrate safe procedures instead of relying on written instructions alone. Show employees how to measure and dilute products, store them as directed, and transfer them only into approved, labeled containers. Make clear that cleaning chemicals should never be mixed unless the manufacturer’s instructions specifically allow it.
Training should also cover how to inspect and operate equipment, including how to spot damaged cords or attachments and report them before use. Explain when ventilation is needed and what to do if a spill occurs, including how to keep others away and notify a supervisor. In healthcare environments, cleaning plans should address PPE, standardized procedures, and cross-contamination prevention. The CDC’s environmental infection-control guidance offers recommendations for healthcare settings. Adapt demonstrations to the actual products, equipment, and conditions at each facility.
Use accessible instructions, hands-on competency checks, and refresher training
Make instructions easy to use during a shift. Short checklists, clear signs, and translated materials can help employees follow procedures accurately. Specify the product, surface, and steps involved, and keep instructions available where the work takes place.
After explaining a task, ask employees to demonstrate it. A supervisor can check that the employee selects the right PPE, follows product directions, and completes each step correctly. Offer coaching if a step is missed, then check again to confirm the employee can perform the task independently. Provide refresher training when a product, piece of equipment, or site requirement changes. Reviewing practices and responding to staff feedback can help keep procedures useful, as Team Clean’s school-cleaning guidance recommends.
Encourage staff to report hazards, exposures, and illness
Employees should know how to report hazards such as damaged equipment, unlabeled containers, chemical spills, or tasks they have not been trained to perform. Explain who to contact, what information to provide, and how to keep others away from an immediate hazard. Supervisors should respond promptly, address the concern, and share relevant follow-up with the team.
Create a clear process for reporting possible chemical exposures, injuries, or work-related illness as well. Staff should know whom to notify and what steps to take next, while managers follow the company’s response and documentation procedures. Encourage employees to speak up without fear of being dismissed. Open communication helps cleaning providers and facility managers address problems early, adjust procedures when needed, and support safer work across every site.
How Should Companies Tailor Cleaning Plans to Each Facility?
A practical cleaning plan reflects how each space is used, who uses it, and which surfaces need regular attention. Facility managers and cleaning providers can agree on tasks, timing, products, and responsibilities, then review the plan when operations or public health guidance changes.
Adapt plans for offices, shared workspaces, and retail environments
In offices and shared workspaces, prioritize high-touch surfaces such as door handles, keyboards, phones, light switches, and shared equipment. Set cleaning frequency according to occupancy and use: a busy conference room or shared kitchen may need more frequent attention than a lightly used private office. In retail spaces, include checkout counters, entrance handles, fitting rooms, and other customer touchpoints in the task list.
Schedule work to limit disruption to employees and customers, and use products according to their labels. A risk-based workplace cleaning approach can help teams identify frequently touched areas and set practical routines. Review the plan with staff who use the space, since they can point out shared surfaces or busy areas that may otherwise be overlooked.
Meet additional infection-control requirements in medical and dental clinics
Medical and dental clinics need cleaning plans that account for patient care, shared equipment, and the facility’s infection-control procedures. Define which areas require cleaning or disinfection, select products labeled for the intended surfaces and uses, and set steps to prevent cross-contamination between rooms. Cleaning staff may also need task-specific training, appropriate personal protective equipment, and procedures for handling supplies and waste.
Coordinate the plan with the clinic’s infection-control lead, and follow applicable public health and workplace requirements. General office routines may not address the needs of treatment rooms or other clinical areas. Establish a way to verify completed tasks and report concerns so the clinic can address missed work promptly. Healthcare cleaning guidance can help inform procedures, but each clinic should confirm that its plan fits its own operations and requirements.
Adapt plans for schools and daycare centers
Schools and daycare centers have changing occupancy, shared learning materials, and spaces used by children throughout the day. Build task lists for classrooms, bathrooms, cafeterias, entrances, and shared equipment, with timing that fits around lessons, meals, and activities. Pay particular attention to frequently touched surfaces, and adjust the schedule based on how heavily each area is used.
Train cleaning staff to handle products safely and follow label directions, including precautions for spaces used by children. Clear instructions can also help teachers and other staff reinforce everyday hygiene practices, such as handwashing and keeping shared areas orderly. Review the plan when attendance, room use, or school activities change. School cleaning recommendations offer ideas for establishing consistent routines while accounting for the needs of students and staff.
Address the needs of warehouses, manufacturing facilities, and large buildings
Warehouses and manufacturing sites may include expansive floors, heavy equipment, break rooms, offices, and busy loading areas. Divide the facility into zones, then set tasks based on surface type, traffic, shift schedules, and operational hazards. Floor care may call for specialized equipment and methods, while shared tools and frequently touched surfaces need attention based on how workers use them.
Coordinate cleaning times with site managers to avoid interrupting production or creating risks around moving vehicles and machinery. Make sure crews understand access rules and any site-specific safety procedures. If an employee becomes ill, follow current public health guidance and the facility’s response plan for areas that person used. This facility cleaning resource discusses considerations such as limiting access and airflow during a response.
Which Misconceptions Can Lead to Poor Cleaning Practices?
Misunderstandings about cleaning and disinfection can waste time, increase chemical exposure, or leave surfaces less clean than intended. A dependable plan uses the right sequence, products suited to the task, and procedures staff can follow safely. These basics matter in every commercial setting, from offices and clinics to retail spaces, schools, and warehouses.
Remember that disinfection does not replace routine cleaning
Cleaning and disinfecting serve different purposes. Cleaning with soap or detergent removes dirt and many germs from a surface. Disinfecting uses a product to kill germs that remain. When a surface is visibly dirty, clean it before disinfecting. Some product labels also require pre-cleaning, so staff should follow the directions for each product.
Prioritize frequently touched surfaces and shared equipment, including door handles, counters, light switches, phones, keyboards, faucets, and restroom fixtures. The right routine depends on how people use the space and the surfaces involved. The CDC’s guidance on cleaning and disinfecting facilities outlines when each step is appropriate. Written task lists can help teams follow the correct sequence without applying the same procedure to every surface.
Recognize that more frequent disinfection is not always safer or more effective
Applying disinfectant to every surface more often than needed does not automatically make a facility healthier. Unnecessary use can expose staff and occupants to chemicals, add costs, and take time away from other essential cleaning tasks. Set a schedule based on how many people use the space, which areas see the most traffic, and the likelihood of contamination.
Routine cleaning may be sufficient when no one with a confirmed or suspected infectious illness has been in the space. If illness or a known exposure changes the risk, review current public health guidance and adjust the plan. The CDC’s facility recommendations can help managers decide when cleaning alone is appropriate and when disinfection is needed. Revisit the schedule when occupancy, facility use, or risk changes.
Know that the EPA registers disinfectants; the CDC does not approve them
The CDC does not approve or register disinfectants. In the United States, the Environmental Protection Agency registers antimicrobial products and reviews their labeled uses. Choose a product registered for its intended purpose and appropriate for the surface, setting, and target germ.
If a facility needs a disinfectant for SARS-CoV-2, check the EPA’s List N. Always read the product label before use. It explains which surfaces the product can be used on, whether dilution is needed, how to apply it, and how long the surface must remain wet. Marketing claims do not replace label directions, and one product may not suit every cleaning task.
Match PPE and cleaning steps to the task and current guidance
Personal protective equipment should match the product and the work. The product label, safety data sheet, or workplace risk assessment may call for gloves, eye protection, or other PPE. Train staff on when to wear it, how to put it on and remove it safely, and what to do after contact with skin or eyes. Requirements can differ between routine office cleaning and higher-risk tasks.
Training should also cover safe dilution, application, contact time, ventilation, equipment use, and spill response. Never mix cleaning chemicals or use a product in a way its label prohibits. The OSHA hazard communication standard explains employers’ responsibilities for communicating chemical hazards. Provide refresher training when products or procedures change, and make sure staff know how to report hazards and possible exposures.
How Can Companies Keep CDC-Aligned Practices Consistent?
Consistency starts with a written plan that turns public health guidance into routines staff can follow and supervisors can check. The plan should reflect the way each facility operates, from a busy retail floor to a medical or dental clinic. It also needs to distinguish routine cleaning from sanitizing and disinfecting, since each task has a different purpose and may require specific products or procedures.
Facility managers and cleaning providers can use the plan to agree on what gets cleaned, how often, which products and equipment are used, and who handles each task. Include instructions for product use, such as dilution, application, and contact time, and make sure workers can access labels and safety information. A clear record also helps teams respond when occupancy, facility use, or public health recommendations change.
Set a regular review schedule and update the plan when a change affects the work. Share revisions with the people who clean, supervise, and manage the facility, then provide training before new procedures begin. These steps support reliable service while giving staff and clients a shared understanding of what the cleaning plan covers.
Document tasks, schedules, products, and staff responsibilities
Create a site-specific plan that lists each task, the area or surface it covers, how often it should be completed, and who is responsible. Identify the products and equipment assigned to each task. Include relevant label instructions, such as dilution, application method, and contact time, and keep product labels and safety data sheets available to staff.
Review the plan with the facility contact so it matches how people use the space. A clinic may need separate routines for patient areas and administrative offices, while a warehouse may need clear assignments for shared equipment and floors. Documenting the work helps teams deliver the agreed service and identify gaps when conditions change. Pair written instructions with demonstrations and practice, following recommendations for effective cleaning staff education.
Use checklists, work orders, supervision, and quality checks
Checklists give staff a practical way to track recurring tasks and confirm when work is complete. In larger buildings, work orders can specify the location, requested task, priority, and completion status. Supervisors can review these records, inspect selected areas, and ask employees whether instructions are clear and workable.
Quality checks should confirm that the agreed tasks were completed and that the plan still suits the facility. If the same issue appears more than once, clarify the procedure, coach staff, or discuss a schedule adjustment with the client. Feedback from facility staff can also reveal areas that need attention. Periodic reviews help schools and other organizations refine cleaning routines, as noted in this school cleaning guidance overview.
Explain service scope and protocol changes to clients
Set expectations before service begins. Explain which areas are included, how often tasks are scheduled, and which requests fall outside the regular scope. This is particularly helpful for property managers responsible for multiple buildings or tenants. Keep a record of agreed changes, such as added tasks, schedule adjustments, or product substitutions.
If guidance or facility conditions call for a protocol change, tell the client what is changing and why. Explain any effect on timing, access, or the work performed, then share updated instructions with staff and the client contact. When working with a janitorial provider, confirm who communicates changes and who approves additional work. Clear communication helps prevent missed tasks and confusion, while reinforcing consistent procedures for identifying high-touch surfaces and reducing cross-contamination risks.
Review current CDC, EPA, OSHA, and local guidance regularly
Assign someone to review applicable guidance on a regular schedule and when facility conditions change. Use current CDC recommendations to inform cleaning procedures, EPA resources to verify disinfectant registration and label directions, and OSHA requirements to guide worker safety. Check state and local rules as well, since they may add requirements for particular facilities or tasks.
Update written procedures when guidance, product labels, or workplace requirements change. Before a new process begins, explain the revision and train staff on the steps that apply to their work. Avoid relying on old checklists or product instructions without confirming they remain current. A scheduled review can help facility managers and cleaning teams keep procedures relevant. This overview of cleaning compliance standards provides additional context on public health and workplace requirements.
Frequently Asked Questions
Does CDC guidance require every surface to be disinfected every day? No. The appropriate routine depends on how a space is used, how often surfaces are touched, and whether there is a specific health concern. Regular cleaning is enough in many situations. Disinfection may be needed when illness, facility policies, or current public health recommendations call for it.
What should facility managers share with a cleaning provider? Share site-specific procedures, areas with restricted access, approved products, operating hours, and any special requirements for clinics, kitchens, or production areas. Also agree on who approves schedule or product changes and how completed work will be recorded.
How can a cleaning team confirm a disinfectant is suitable? Check the EPA registration and product label. Confirm that the product is intended for the surface and use, then follow instructions for dilution, application, contact time, ventilation, and protective equipment. For COVID-19 concerns, consult EPA List N and verify the product’s label directions.
What should a facility do after a person with COVID-19 has been on site? Contact the facility manager and identify the areas the person used and when they were last there. Then check current public health guidance, coordinate access, and determine which cleaning or disinfection steps are appropriate. Keep a record of the work completed and the products used.
How can businesses check that cleaning procedures are being followed? Use site-specific task lists and completion records, then have supervisors inspect selected areas and gather feedback from facility staff. If a task is repeatedly missed or conditions change, clarify the instructions or revise the schedule and train the team on the update.
